Joined in 2023 
82 
63 About this deal
The SATA cables are up to 40 inches. So it is an advantage of SATA over IDE which is the management of cables and length of the cables connecting the hard drives and motherboard. When you have extra length in cables, more flexibility of the positions of the drive can be attained. Then, to the hard drive connection point, attach the free end of the converter cable. Depending on the connection point, sometimes it will be necessary to attach the free end of the cable to the IDE cable.
SATA consists of an 8 mm wide wafer connector on each end and the cable has a 7-pin connector, 3 grounds and 4 active data lines in two pairs. It has the facility to attach only one drive and so Serial ATA does away with Master/Slave configurations. While it is possible to make the necessary changes if drivers are required to run that type of drive it is a lot of messing around. Also if Windows has been loaded for more that 12 months it’s better to do a Clean Install so you can get rid of all the crud that clogs up the Registry.But the SATA bus is a serial point-to-point bus, which means only one device can be connected on each channel. Many SATA drives can connect to the motherboard via multiple ports, and the drive to boot from is specified in the BIOS settings. Data transfer speed for IDE ranges from 5MB/s up to 133MB/s (ATA100/133). The parallel wire transfer mode reached its limit with the speed of 133 MB/s. Moreover, the total switch from IDE to SATA doesn’t happen without issues sometimes. If you have an IDE hard drive but have a SATA motherboard, you can connect the drive to the motherboard still. This may be your reason for the conversion of IDE to SATA. Connecting the IDE Hard Drive to SATA Motherboard
IDE Hard Drive: It is one of the most elements that’s needed. You know by now what IDE is. IDE hard drives are easily identifiable through their pin connection points usually. In most of the cases, the installation is by plugging it into the required component. It is needed to ensure a tight connection. SATA drives have an additional feature of Hot plugging which mean that even as the computer is running drives can be removed or added. Yes, SATA is faster than IDE. It is the newer standard and should always be chosen over the older IDE connectors. While IDE offers data speed of up to 133 MB/s, SATA can transfer data at 6 Gb/s. Can a USB to SATA power a HDD? It may even work with a SATA Drive but not a SSD Drive as while these days they are interchangeable in the past they where not always so. Also the hardware always treats IDE Drives as the Default Master Drive and writes the Boot Loaded to that Drive so it’s important after the Clone to remove the IDE Drive before starting the system on the SSD Drive. USB ports can only deliver so much electricity to power portable HDDs, not regular HDDs. So, you will need to use a separate power adapter. How do I know if my HDD is SATA or IDE?There are four to six SATA connections usually in a normal motherboard which allows multiple SATA hard drives to hook up. SATA has also done away with the master/slave configuration (technically, device 0 and device 1) used in IDE drives. With PATA (IDE), attaching two hard disks to the same channel required one to be set to be the master, the other the slave. For hardware, this usually meant setting the right jumper settings.
Lastly, close your computer case. After plugging in power supply, boot your computer. There might be some last setup procedures that’ll take place at the time of the boot process, if either your IDE drive is somehow new or has no data stored on it. You should always follow any on-screen In most cases, no additional set up is usually necessary and you will find the drive simply available for storage use.
IDE To SATA Converter
SATA motherboard: As you know, SATA is the current standard for the connection of hard drive to the motherboard. This is obviously a replacement for the previous IDE connection. It is easily identifiable by the simple plug with only one connection point. SATA motherboards are more likely the present standards and are more efficient, faster, and more stable. You will feel when you will know about it that connecting the IDE hard drive to the SATA motherboard is a very easy task. It will take at most 10-20 minutes. Remember that the computer must be unplugged from any electrical connection. SATA took off where ATA stopped as far as speed is concerned. The first generation of SATA was 1.2 Gbit/s (150 MB/s; note that MB is mega bytes and Gb is giga bits) similar to PATA/133. Today the third generation of SATA (3.0) (released on May 27, 2009), 6 Gbit/s (600 MB/s) hard drives and motherboards are being used.
The main motivation behind the creation of SATA was the increase in the drive speed. For, SATA connection hard drives are very fast. Advantages of SATAAfter many days of IDE connection hard drives, there came the SATA hard drives which are meant to replace the IDE hard drives for their more efficient characteristics. SATA means ‘Serial Advanced Technology Attachment’. The main characteristic which differentiates SATA from PATA or IDE is that in SATA the information moves between the hard drive and motherboard as serial one, i. e. one bit after another. The SATA drives usually need very little power than PATA drives. The SATA drive usually uses only 250 mV of power, which is even 25 percent of one volt. The lower power consumption of SATA connection drives helps to keep the inner part of the computer case cooler and also reduces the power supply drain at a considerable range.
Related:
Great Deal 
New Comment